APRS Track Direct

My position About ☰

reset

KC2G Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KC2G. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	BatTemp*	Bat*	Solar*
1766804181	24 deg.F	13.2 V	10 V
1766803281	24 deg.F	13.2 V	10 V
1766802381	24 deg.F	13.2 V	10 V
1766801481	24 deg.F	13.2 V	10 V
1766800581	24 deg.F	13.2 V	10 V
1766799680	24 deg.F	13.2 V	10 V
1766798781	24 deg.F	13.2 V	10 V
1766797880	24 deg.F	13.2 V	10 V
1766796981	24 deg.F	13.2 V	10 V
1766796080	24 deg.F	13.2 V	10 V
1766795181	24 deg.F	13.2 V	10 V
1766794280	24 deg.F	13.2 V	10 V
1766793381	24 deg.F	13.2 V	10 V
1766792480	24 deg.F	13.2 V	10 V
1766791581	24 deg.F	13.2 V	10 V
1766790681	24 deg.F	13.2 V	10 V
1766789781	24 deg.F	13.2 V	10 V
1766788880	24 deg.F	13.2 V	10 V
1766787981	25.5 deg.F	13.2 V	10 V
1766787080	26 deg.F	13.2 V	10 V
1766786181	26 deg.F	13.2 V	10 V
1766785280	26 deg.F	13.2 V	10 V
1766784381	27 deg.F	13.2 V	10 V
1766783480	27 deg.F	13.2 V	15 V
1766782581	27 deg.F	13.2 V	20.35 V

*Used Equation Coefficients:

BatTemp: 0, 0.5, 0

Bat: 0, 0.05, 10

ChgA: 0, 0.05, 0

Solar: 0, 0.05, 10

Chg: 0.002, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)