APRS Track Direct

My position About ☰

reset

DO5MF-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DO5MF-5. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*	Value3*	Value4*	Value5*
1766805344	49	5653	7570	2203	4270
1766804743	49	5652	7563	2205	4268
1766804142	49	5656	7572	2204	4266
1766803541	49	5655	7570	2205	4265
1766802940	49	5655	7571	2207	4262
1766802339	49	5655	7572	2209	4264
1766801738	49	5655	7570	2210	4264
1766801137	49	5654	7569	2210	4264
1766800536	49	5654	7567	2211	4264
1766799935	49	5656	7571	2213	4263
1766799334	49	5656	7570	2215	4259
1766798733	49	5655	7570	2216	4265
1766798132	49	5658	7568	2217	4265
1766797531	48	5655	7569	2219	4267
1766796930	48	5652	7565	2219	4268
1766796329	48	5653	7567	2219	4271
1766795728	48	5655	7568	2221	4268
1766795127	48	5656	7568	2222	4267
1766794526	48	5658	7573	2224	4266
1766793926	48	5658	7572	2226	4264
1766793324	48	5658	7570	2226	4266
1766792723	48	5659	7572	2228	4264
1766792122	48	5657	7572	2230	4264
1766791521	48	5656	7571	2232	4263
1766790920	48	5655	7567	2235	4263

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)