APRS Track Direct

My position About ☰

reset

9M2FUL-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 9M2FUL-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Value1*	Value2*	Value3*	Value4*	Value5*
1766823591	33.43	46	1002	2.52	24
1766823574	33.47	46	1001	2.53	19
1766823557	33.5	46	1001	2.53	23
1766823546	33.52	46	1001	2.54	22
1766823523	33.56	47	1001	2.56	18
1766823506	33.56	46	1001	2.57	21
1766823489	33.59	47	1001	2.59	22
1766823472	33.61	46	1001	2.59	22
1766823461	33.63	46	1001	2.59	20
1766823438	33.65	46	1000	2.61	16
1766823427	33.68	46	998	2.61	21
1766823404	33.7	46	998	2.65	17
1766823393	33.72	46	998	2.64	15
1766823281	33.84	46	998	2.66	20
1766823263	33.77	46	994	2.68	41
1766823252	33.77	46	994	2.59	38
1766823243	33.79	46	994	2.59	38
1766823203	33.83	46	992	2.74	39
1766823182	33.86	46	991	2.74	35
1766823173	33.86	46	991	2.74	35
1766823085	33.95	46	986	2.79	36
1766822555	34.24	47	948	3.01	35
1766819589	35.63	45	998	3.37	32
1766819556	35.68	45	999	3.37	34
1766819523	35.75	45	1000	3.37	38

*Used Equation Coefficients:

Value1: 0, 0.01, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 0.01, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)